Page 2 of 2 FirstFirst 12
Results 26 to 34 of 34

Carpenter SP vs Smith Tokara

This is a discussion on Carpenter SP vs Smith Tokara within the Popping Style forums, part of the Saltwater Fishing category; I think those peanuts are made by the man sitting at the end of Sabre..... Hehehehehe!!!!! All his rods have ...

  1. #26
    Moderator jason's Avatar
    Join Date
    Mar 2004
    Location
    Singapore
    Posts
    754
    Rep Power
    8

    RE: carpenter rod epoxy

    I think those peanuts are made by the man sitting at the end of Sabre.....
    Hehehehehe!!!!!
    All his rods have a trademark of Muscles!!!!!Big biceps!!!!But his epoxy is still one of the best!!!


    Cheers
    Jason

  2. #27
    Member mKim's Avatar
    Join Date
    Mar 2005
    Location
    sg
    Posts
    54
    Rep Power
    7

    epoxy

    aiya......Jason...cannot say openly what. not nice to mentioned shop or builder's name...hahaha


    I had quite a few rods with peanut epoxy too...but I kind of like them.
    However, the "peanut" is not very peanut on Carpenter rods....more like a "kidney". A bit too big....

    So, was wondering if in the process of custom making a rod, can we request for smaller & neater epoxy?

    Rgds
    MKim

  3. #28
    Moderator jason's Avatar
    Join Date
    Mar 2004
    Location
    Singapore
    Posts
    754
    Rep Power
    8

    RE: epoxy

    Hi mkim
    If its custom build I am very sure it is possible.....
    But if it is its trade mark, then its different story.....



    Cheers
    jason

  4. #29
    Super Moderator stickbom!'s Avatar
    Join Date
    Jan 2004
    Location
    Eastern Sider
    Posts
    2,609
    Rep Power
    11

    Re: carpenter rod epoxy

    Quote Originally Posted by mKim
    Hi all....just nice to see some discussion here on carpenter rods, and good to know that some are owners of it.
    Been wanting to get a carpenter jigging and popping rod but so far not much choice from the local scene. But when I tried to order from them, they refer me back to the local agent here.
    Anyway, i am looking at a custom built one not their factory rod.
    Any difference between their custom built and factory rods especially in terms of the epoxy?
    Knew of some anglers who complain about some rod builders in Singapore who likes to do 'kidney' or 'peanut' epoxy on the guides , but just check out those large "kidneys" on Carpenter rods...
    I saw the jig/ popping rods at Richards' shop.... wanted to get one but its the epoxy that puts me off.

    Anyone here knows how to place an direct order with carpenter (instead of going through so many parties) for a customised popping rod and also if its possible to request them to thin down the epoxy a little?

    Advance thanks to owners of Carpenter rods....

    Cheers!
    MKim
    Spoke to Adrian @ Angler's Hut sometime ago and he told me there's an custom order form now, go check it out. Try and contact "Sportfisherman" if the local dealer cannot help you.

  5. #30
    Member mKim's Avatar
    Join Date
    Mar 2005
    Location
    sg
    Posts
    54
    Rep Power
    7

    custom built

    ok will do. thanks for the contact.
    had spoken to richard much earlier about this issue in jan, but find it very troublesome and draggy. anyway, that time i only mentioned about the thread/ blank color, none on the spec of the rod. wonder if they can do it according to your specs or u just get to choose the color of the binds and drawings on the rod only, where the handle length and choice of guides is entirely up to them.

    how the epoxy on your custom carpenter rods anyway? hope they are not as huge as those factory ones.

    rgds
    MKim

  6. #31
    Super Moderator stickbom!'s Avatar
    Join Date
    Jan 2004
    Location
    Eastern Sider
    Posts
    2,609
    Rep Power
    11

    Re: custom built

    Quote Originally Posted by mKim
    ok will do. thanks for the contact.
    had spoken to richard much earlier about this issue in jan, but find it very troublesome and draggy. anyway, that time i only mentioned about the thread/ blank color, none on the spec of the rod. wonder if they can do it according to your specs or u just get to choose the color of the binds and drawings on the rod only, where the handle length and choice of guides is entirely up to them.

    how the epoxy on your custom carpenter rods anyway? hope they are not as huge as those factory ones.

    rgds
    MKim
    No complaints for my custom jobs. Hope you get yours worked out soon.

  7. #32
    Member mKim's Avatar
    Join Date
    Mar 2005
    Location
    sg
    Posts
    54
    Rep Power
    7

    custom rod

    Good....glad to hear that. you mind showing some close up pic of your csutom carpenter rods? On the expoxy and the handle esp?

    rgds
    MKim

  8. #33
    Super Moderator stickbom!'s Avatar
    Join Date
    Jan 2004
    Location
    Eastern Sider
    Posts
    2,609
    Rep Power
    11
    Yes Sir! I'll do it when I get back my digital camera.

  9. #34
    Member mKim's Avatar
    Join Date
    Mar 2005
    Location
    sg
    Posts
    54
    Rep Power
    7

    thanks

    appreciated n thanks

    will be waiting for ther pics

    Rgds'

Page 2 of 2 FirstFirst 12

Similar Threads

  1. WTB Smith wrc/35
    By Madfisho in forum Popping Style
    Replies: 0
    Last Post: 28-07-2009, 08:58 PM
  2. Help needed for Carpenter, Smith and Zenaq popping rods
    By seamonster in forum Popping Style
    Replies: 13
    Last Post: 09-02-2008, 08:43 PM
  3. Tokara Marine Challenger Videos
    By MarkR in forum Chatter Box
    Replies: 3
    Last Post: 19-12-2006, 12:21 AM

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •